1

Available Specification size of aluminum sheet and aluminum coils


1.1 Available Specification size of alloy and temper comparative table

Alloy Standards Temper Remark

1070

AA,JIS

F,O,H1n

H1n : H12,H14,H16,H18

1050

AA,JIS

F,O,H1n

"

1100

AA,JIS

F,O,H1n

"

3003

AA,JIS

F,O,H1n

"

5052

AA,JIS

F,O,H1n,H3n

H3n : H32,H34,H36,H38

5657

AA,JIS

F,O,H2n

H2n : H241,H25,H26,H28


1.2 Available Specification size of temper and thickness comparative table

Temper

Thickness mm

Specification

Remark

F

0.15-6.50

AA,JIS

5052 negotiated

O

0.15-6.50

AA,JIS

5052 negotiated

H12,H32

0.50-3.20

AA,JIS

-----

H14,H34

0.50-2.50

AA,JIS

-----

H16

0.25-2.00

AA,JIS

-----

H36

0.40-1.60

AA,JIS

5052 only

H18

0.15-1.00

AA,JIS

-----

H38

0.30-0.80

AA,JIS

5052 only

*5657 negotiated

2

Chemical Composition


unit :Wt %  

Composition
Alloy

Si

Fe

Cu

Mn

Mg

Cr

Zn

Ti

Ga

V

Al

                       

1070

0.20

0.25

0.04

0.03

0.03

--

0.04

0.03

--

--

99.70

1050

0.25

0.40

0.05

0.05

0.05

--

0.05

0.03

--

--

99.50

1100

0.95

0.05 - 0.20

0.05

--

--

0.10

--

--

--

99.00

3003

0.60

0.70

0.05 - 0.20

1.00 - 1.50

--

--

0.10

--

--

--

REM

5052

0.25

0.40

0.10

0.10

2.20 - 2.80

0.15 - 0.35

0.10

--

--

--

REM

5657

≦0.08

≦0.1

≦0.1

≦0.03

0.6-1.0

--

≦0.05

--

≦0.03

≦0.05

REM

  Remark: The chemical composition of Al is the min, the others is max.


3

Mechanical Properties

 

3.1 1070

Alloy
&
Temper

Thickness mm

Tensile Strength

Ultimate kgf/mm2

Yield kgf/mm2

Elongation %

1070-O

0.20 – 0.50
0.51 – 0.80
0.81 – 1.28
1.29 – 6.00

5.6min

9.6max

--
--
1.5min
1.5min

15
25
30
35

1070-H12

0.20 – 0.50
0.51 – 0.80
0.81 – 1.28
1.29 – 4.00

7.1min

11.2max

--
--
5.6max
5.6max

2
4
6
8

1070-H14

0.20 – 0.50
0.51 – 0.80
0.81 – 1.28
1.29 – 3.10

8.67min

12.2max

--
--
6.6max

--

1
3
4
5

1070-H16

0.20 – 0.50
0.51 – 0.80
0.81 – 1.28
1.29 – 2.10

10.2min

13.7max

7.6max

1
2
3
4

1070-H18

0.20 – 0.50
0.51 – 0.80
0.81 – 1.20

12.2min

--

1
2
3

Remark:

  1. GL = 50.8 mm.
 

3.2 1050

Alloy
&
Temper

Thickness mm

Tensile Strength

Ultimate kgf/mm2

Yield kgf/mm2

Elongation %

1050-O

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 6.00

6.0min

10.0max

2.0min

15
20
25
30

1050-H12

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 4.00

8.0min

12.0max

6.5min

3
4
6
8

1050-H14

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 3.10

9.5min

13.0max

7.5min

1
3
4
5

1050-H16

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 2.10

12.0min

15.0max

8.5min

1
2
3
4

1050-H18

0.20 – 0.46
0.47 – 0.80
0.81 – 1.20

13.0min

--

1
2
3

 

3.3 1100

Alloy
&
Temper

Thickness mm

Tensile Strength

Ultimate kgf/mm2

Yield kgf/mm2

Elongation %

1100-O

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 3.20
3.21– 6.00

7.7min

10.9max

2.4min

15
20
25
28
28

1100-H12

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 3.20
3.21 – 4.00

9.8min

13.3max

7.7min

3
4
5
8
8

1100-H14

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 3.10

11.2min

14.7max

9.8min

1
2
3
5

1100-H16

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 2.10

13.3min

16.8max

11.9max

1
2
3
4

1100-H18

0.20 – 0.46
0.47 – 0.80
0.81 – 1.20

15.4min

--

1
1
2

 

3.4 3003

Alloy
&
Temper

Thickness mm

Tensile Strength

Ultimate kgf/mm2

Yield kgf/mm2

Elongation %

3003-O

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 3.20
3.21 – 6.30

9.8min

13.3max

3.5min

14
18
20
25
23

3003-H12

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 3.30

11.9min

16.1max

8.4min

3
4
5
6

3003-H14

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 2.60

14.0min

18.2max

11.9min

1
2
3
4

3003-H16

0.20 – 0.46
0.47 – 0.80
0.81 – 1.80

16.8min

21.0max

14.7min

1
2
3

3003-H18

0.20 – 0.46
0.47 – 0.80
0.81 – 1.00

18.9min

16.8min

1
2
3

 

3.5 5052

Alloy
&
Temper

Thickness mm

Tensile Strength

Ultimate kgf/mm2

Yield kgf/mm2

Elongation %

5052-O

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.60 – 4.20

17.5min

21.8max

6.6min

13
15
17
19

5052-H32

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.60 – 3.30

21.8min

26.7max

16.2min

3
4
5
7

5052-H34

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.60 – 2.60

23.9min

28.9max

18.3min

3
3
4
6

5052-H36

0.20 – 0.46
0.47 – 0.80
0.81 – 1.80

25.9min

30.9max

20.3min

2
3
4

5052-H38

0.20 – 0.46
0.47 – 0.80
0.81 – 1.60
1.61 – 3.20

27.4min

22.3min

2
3
4
4

 

3.6 5657

Alloy
&
Temper

Thickness mm

Tensile Strength

Ultimate kgf/mm2

Yield kgf/mm2

Elongation %

5657-H241

0.8 - 2.3

12.67min

18.28max

--

13.0

5657-H25

0.8 - 2.3

14.06min

19.69max

--

≧8.0

5657-H241

0.8 - 2.3

14.47min

21.09max

--

≧7.0

5657-H241

0.8 - 2.3

≧17.58

--

≧5.0


4

Width Tolerances

unit : mm

Thickness

Width

Tolerances

Thickness

Width

Tolerances

~ 0.6

~ 50

± 0.10

2.01 ~ 3.2

~ 50

± 0.20

50 ~ 150

± 0.15

50 ~ 150

± 0.30

151 ~ 300

± 0.30

151 ~ 300

± 0.50

301 ~ 600

± 0.50

301 ~ 600

± 1.00

601 ~ 1247

± 1.00

601

± 1.50

0.6 ~ 1.0

~ 50

± 0.15

3.21 ~

~ 50

± 0.30

50 ~ 150

± 0.15

50 ~ 150

± 0.50

151 ~ 300

± 0.30

151 ~ 300

± 1.00

301 ~ 600

± 0.60

301 ~ 600

± 1.20

601

± 1.20

601

± 1.50

1.01 ~ 2.0

~ 50

± 0.15

 

50 ~ 150

± 0.20

151 ~ 300

± 0.40

301 ~ 600

± 1.00

601

± 1.50

Remark :
1.If all the tolerances are positive(0) or all negative, the data must double.
2.The tolerances of thickness and width without the above list must agree on buyer and seller.

5

Thickness Tolerances

unit : mm

Alloy

Thickness

1XXX&3003

5052

Tolerances

Tolerances

0.2 ~0.6

± 0.02

± 0.04

0.61 ~ 1.5

± 0.03

± 0.06

1.51 ~ 2.5

± 0.04

± 0.08

2.51 ~ 4.5

± 0.06

± 0.10

4.51 ~ 7.35

± 0.08

± 0.12

7.36 ~(hot roll)

± 0.25

± 0.40

Remark:

  1. If all the tolerances are positive(0) or all negative, the data must double.
  2. The tolerances of thickness and width without the above list must agree on buyer and seller.

6

Length Tolerances

unit : mm

Thickness

Length

Max

7.35

750

+2

7.36

1220

+30

Remark: max length 4M.

7

Dimension Tolerances

The max squareness : thickness under 7.35mm and length under 4 M that the max difference of diagonal line 2 mm, width without limited.

8

Flatness Tolerances

unit : mm

Thickness

Wavelength

Max

0.4 ~ 1.6

~ 610

6

610 ~ 915

6

916 ~ 1220

6

1221

8

1.6 ~ 4.0

~ 610

6

611 ~ 915

8

916 ~ 1220

8

1221

10

4.0

~ 610

8

611 ~ 915

10

916 ~1220

10

1221

12

9

Short-span flatness Tolerances

Thickness

Max

0.4 ~ 1.6

8

1.6 ~ 6.0

10

Remark:
The thickness of max short-span flatness without the above list must agree on buyer and seller.

10

Transverse flatness Tolerances

Width

Thickness

Max

300 ~ 600

600 ~1220

0.4 ~ 1.6

5

8

1.6 ~ 6

7

10

Remark:
The thickness and width of max transverse flatness without the above list must agree on buyer
and seller.

11

Surface Appearance

11.1 Surface smooth.

11.2 Substantially free from inclusion, blister, roll-in metal, brokenedge, dent, kink, corrosion.

11.3 Allowed light lick-up, shut, oil stain, scratch, edge wave.

11.4 The special request must agree on buyer and seller.

Association

Abbreviation

Association

AA

Aluminum Association

AMS

Aerospace Material Specification

ANSI

American National Standards Institute

AS

Australian Standards

ASME

American Society of Mechanical Engineers

ASTM

American Society for Testing & Materials

AWS

American Welding Society

BS

British Standards

CNS

Chinese National Standards

CSA

Canadian Standards Association

DIN

Deutsche Industrie – Normen

FS

Federal Specifications

ISO

International Organization for Standardization

JISO

Japanese Automobile Standards Organization

JIS

Japanese Industrial Standards

MIL

Military Specification

SAE

Society of Automotive Engineers

 

 



2021 ©Copyright byTaiwell Aluminum Corporation.